為了保障生產安全，生產企業針對不同的生產工序已經制定了一系列的操作規程，包括設備使用與人員工作等；

工作中須遵守本操作規程：

  1、工作前須檢查電氣開關及線路，溫控儀、時間繼電器及烘箱外殼的接地是否完整，經試驗合格后放可投入使用。
  2、烘箱附近不準放置易燃易爆物品，并保持周圍環境整潔。
  3、須經常檢查烘箱的蒸氣導氣閥，保障有效可靠。
  4、送焊條進烘箱時，須切斷電源。材料取出后須加強烘箱內檢查，防止焊條或雜物落在電熱管帶電體上，造成短路或觸電事故。箱內物品不建議放置太擠，以免影響熱風循環，造成溫度不均或發生其他不安全的隱患。
  5、焊條烘焙的時候，操作人員不要離開烘箱的周圍。烘箱的各個參數設置須由專人操作，并根據所烘物品的不同工藝要求設置相應的各項參數，其他人員不得擅自更改。
  6、須保持烘箱內整潔并仔細檢查清理烘箱內電阻絲旁的氧化皮。
  7、烘烤結束后，關閉烘箱電源，打開烘箱門，待物品冷卻后方可取出，防止燙傷。
  8、注意其容易發生危險的范圍內人員和其他事物的安全。經常保持箱內的清潔并保持箱外地面清潔。不宜將過重的物品放入箱內。定期校對溫度控制儀溫度顯示是否超差。從烘箱內取出已烘物品時請戴好防護用品以免燙到。
  焊條烘箱功率是多少？
  比如100型焊條烘箱功率是4KW/220V，焊條烘箱發熱元件均采用新一代遠紅外不銹鋼電熱管加熱，并采用分層布置，具有升溫快、熱慣性小、效率高及節能之特點；極限工作溫度達500℃，可以滿足各種電焊條的脫水烘干，是焊接待業必備的理想烘干設備。

In order to ensure production safety, production enterprises have formulated a series of operating procedures for different production processes, including equipment use and personnel work;
This operating procedure must be followed during work:
1. Before operation, check whether the grounding of electrical switch and circuit, temperature controller, time relay and oven shell is complete, and put them into use after passing the test.
2. Flammable and explosive materials shall not be placed near the oven, and the surrounding environment shall be kept clean.
3. The steam guide valve of the oven must be checked frequently to ensure its effectiveness and reliability.
4. Cut off the power supply when sending welding rods into the oven. After the materials are taken out, the inspection in the oven must be strengthened to prevent welding rods or sundries from falling on the electrified body of the electric heating tube, causing short circuit or electric shock accidents. It is not recommended to place the articles in the box too crowded to avoid affecting the hot air circulation, causing uneven temperature or other unsafe hazards.
5. When baking the welding rod, the operator shall not leave around the oven. The setting of each parameter of the oven must be operated by a specially assigned person, and the corresponding parameters shall be set according to the different process requirements of the baked articles. Other personnel shall not change them without authorization.
6. Keep the oven clean and tidy, and carefully check and clean the oxide skin beside the resistance wire in the oven.
7. After baking, turn off the power supply of the oven, open the oven door, and take out the items after they are cooled to prevent scalding.
8. Pay attention to the safety of people and other things within the scope where they are prone to danger. Keep the box clean and the ground outside the box clean. It is not suitable to put overweight articles into the box. Regularly check whether the temperature display of the temperature controller is out of tolerance. Please wear protective equipment when taking out the baked articles from the oven to avoid scalding.
What is the power of electrode oven?
For example, the power of Model 100 electrode oven is 4KW/220V, and the heating elements of the electrode oven are all heated by a new generation of far-infrared stainless steel electric heating tubes, which are arranged in layers, featuring fast temperature rise, small thermal inertia, high efficiency and energy conservation; The extreme working temperature reaches 500 ℃, which can meet the dehydration and drying of various welding electrodes. It is an ideal drying equipment necessary for welding.